diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig
index d17337c0c3f..1b06d8a66c7 100644
--- a/drivers/power/Kconfig
+++ b/drivers/power/Kconfig
@@ -58,6 +58,7 @@ choice
 	default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
 	default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
 	default AXP818_POWER if MACH_SUN8I_A83T
+	default AXP318W_POWER if MACH_SUN60I_A733
 	default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_V3S
 
 config SUNXI_NO_PMIC
@@ -140,6 +141,14 @@ config AXP818_POWER
 	Say y here to enable support for the axp818 pmic found on
 	A83T dev board.
 
+config AXP318W_POWER
+	bool "axp318w pmic support"
+	select AXP_PMIC_BUS
+	select CMD_POWEROFF
+	---help---
+	Select this to enable support for the AXP318W PMIC found on some
+	A733 boards.
+
 config SY8106A_POWER
 	bool "SY8106A pmic support"
 	depends on MACH_SUNXI_H3_H5
@@ -154,6 +163,7 @@ config AXP_I2C_ADDRESS
 	depends on ARCH_SUNXI && !SUNXI_NO_PMIC
 	default 0x36 if AXP305_POWER
 	default 0x36 if AXP313_POWER
+	default 0x36 if AXP318W_POWER
 	default 0x30 if AXP152_POWER
 	default 0x34
 	---help---
diff --git a/drivers/power/pmic/axp.c b/drivers/power/pmic/axp.c
index 1204ec00f8d..7d8348b0769 100644
--- a/drivers/power/pmic/axp.c
+++ b/drivers/power/pmic/axp.c
@@ -95,6 +95,7 @@ static const struct udevice_id axp_pmic_ids[] = {
 	{ .compatible = "x-powers,axp806", .data = AXP806_ID },
 	{ .compatible = "x-powers,axp809", .data = AXP809_ID },
 	{ .compatible = "x-powers,axp813", .data = AXP813_ID },
+	{ .compatible = "x-powers,axp318w", .data = AXP318_ID },
 	{ }
 };
 
diff --git a/drivers/power/regulator/axp_regulator.c b/drivers/power/regulator/axp_regulator.c
index 7794a4f5d92..34c575e16eb 100644
--- a/drivers/power/regulator/axp_regulator.c
+++ b/drivers/power/regulator/axp_regulator.c
@@ -189,6 +189,55 @@ static const struct axp_regulator_plat axp313_regulators[] = {
 	{ }
 };
 
+ /*
+  * Only two level step tuning is implemented for DCDC6, 8, 9
+  * so the voltage below is not support in this driver
+  * DCDC6:   20  (v1.8 - 2.4v), 40 (2.44v - 2.76v)
+  * DCDC8,9: 100 (1.9v - 3.4v)
+  */
+static const struct axp_regulator_plat axp318_regulators[] = {
+	{ "dcdc1", 0x10, BIT(0), 0x12, 0x1f,  1000, 3400,  100, 0 },
+	{ "dcdc2", 0x10, BIT(1), 0x13, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc3", 0x10, BIT(2), 0x14, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc4", 0x10, BIT(3), 0x15, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc5", 0x10, BIT(4), 0x16, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc6", 0x10, BIT(5), 0x17, 0x7f,  500, 1540,  10, 70 },
+	{ "dcdc7", 0x10, BIT(6), 0x18, 0x7f,  500, 1840,  10, 70 },
+	{ "dcdc8", 0x10, BIT(7), 0x19, 0x7f,  500, 1840,  10, 70 },
+	{ "dcdc9", 0x11, BIT(0), 0x1a, 0x7f,  500, 1840,  10, 70 },
+	{ "aldo1", 0x20, BIT(0), 0x24, 0x1f,  500, 3400, 100, NA },
+	{ "aldo2", 0x20, BIT(1), 0x25, 0x1f,  500, 3400, 100, NA },
+	{ "aldo3", 0x20, BIT(2), 0x26, 0x1f,  500, 3400, 100, NA },
+	{ "aldo4", 0x20, BIT(3), 0x27, 0x1f,  500, 3400, 100, NA },
+	{ "aldo5", 0x20, BIT(4), 0x28, 0x1f,  500, 3400, 100, NA },
+	{ "aldo6", 0x20, BIT(5), 0x29, 0x1f,  500, 3400, 100, NA },
+	{ "bldo1", 0x20, BIT(6), 0x2a, 0x1f,  500, 3400, 100, NA },
+	{ "bldo2", 0x20, BIT(7), 0x2b, 0x1f,  500, 3400, 100, NA },
+	{ "bldo3", 0x21, BIT(0), 0x2c, 0x1f,  500, 3400, 100, NA },
+	{ "bldo4", 0x21, BIT(1), 0x2d, 0x1f,  500, 3400, 100, NA },
+	{ "bldo5", 0x21, BIT(2), 0x2e, 0x1f,  500, 3400, 100, NA },
+	{ "cldo1", 0x21, BIT(3), 0x2f, 0x1f,  500, 3400, 100, NA },
+	{ "cldo2", 0x21, BIT(4), 0x30, 0x1f,  500, 3400, 100, NA },
+	{ "cldo3", 0x21, BIT(5), 0x31, 0x1f,  500, 3400, 100, NA },
+	{ "cldo4", 0x21, BIT(6), 0x32, 0x1f,  500, 3400, 100, NA },
+	{ "cldo5", 0x21, BIT(7), 0x33, 0x1f,  500, 3400, 100, NA },
+	{ "dldo1", 0x22, BIT(0), 0x34, 0x1f,  500, 3400, 100, NA },
+	{ "dldo2", 0x22, BIT(1), 0x35, 0x1f,  500, 3400, 100, NA },
+	{ "dldo3", 0x22, BIT(2), 0x36, 0x1f,  500, 3400, 100, NA },
+	{ "dldo4", 0x22, BIT(3), 0x37, 0x1f,  500, 3400, 100, NA },
+	{ "dldo5", 0x22, BIT(4), 0x38, 0x1f,  500, 3400, 100, NA },
+	{ "dldo6", 0x22, BIT(5), 0x39, 0x1f,  500, 3400, 100, NA },
+	{ "eldo1", 0x22, BIT(6), 0x3a, 0x1f,  500, 1500, 25, NA },
+	{ "eldo2", 0x22, BIT(7), 0x3b, 0x1f,  500, 1500, 25, NA },
+	{ "eldo3", 0x23, BIT(0), 0x3c, 0x1f,  500, 1500, 25, NA },
+	{ "eldo4", 0x23, BIT(1), 0x3d, 0x1f,  500, 1500, 25, NA },
+	{ "eldo5", 0x23, BIT(2), 0x3e, 0x1f,  500, 1500, 25, NA },
+	{ "eldo6", 0x23, BIT(3), 0x3f, 0x1f,  500, 1500, 25, NA },
+	{ "dc1sw1", 0x11, BIT(3),  NA,   NA,   NA,   NA, NA, NA },
+	{ "dc1sw2", 0x11, BIT(4),  NA,   NA,   NA,   NA, NA, NA },
+	{ }
+};
+
 /*
  * The "dcdc2" regulator has another range, beyond 1.54V up to 3.4V, in
  * steps of 100mV. We cannot model this easily, but also don't need that,
@@ -318,6 +367,7 @@ static const struct axp_regulator_plat *const axp_regulators[] = {
 	[AXP221_ID]	= axp22x_regulators,
 	[AXP223_ID]	= axp22x_regulators,
 	[AXP313_ID]	= axp313_regulators,
+	[AXP318_ID]	= axp318_regulators,
 	[AXP323_ID]	= axp313_regulators,
 	[AXP717_ID]	= axp717_regulators,
 	[AXP803_ID]	= axp803_regulators,
diff --git a/include/axp_pmic.h b/include/axp_pmic.h
index 1806a7270a0..2f547da74c2 100644
--- a/include/axp_pmic.h
+++ b/include/axp_pmic.h
@@ -39,6 +39,7 @@ enum {
 	AXP806_ID,
 	AXP809_ID,
 	AXP813_ID,
+	AXP318_ID,
 };
 
 int axp_set_dcdc1(unsigned int mvolt);