diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c
index ba414306c98a..ea33aa644cda 100644
--- a/drivers/tty/serial/8250/8250_dw.c
+++ b/drivers/tty/serial/8250/8250_dw.c
@@ -52,6 +52,7 @@
 #define DW_UART_QUIRK_CPR_VALUE		BIT(5)
 #define DW_UART_QUIRK_IER_KICK		BIT(6)
 #define DW_UART_QUIRK_SKIP_EMPTY_FIFO_READ	BIT(7)
+#define DW_UART_QUIRK_NO_DLF		BIT(8)
 
 /*
  * Number of consecutive IIR_NO_INT interrupts required to trigger interrupt
@@ -606,6 +607,8 @@ static void dw8250_quirks(struct uart_port *p, struct dw8250_data *data)
 		p->serial_out = dw8250_serial_out38x;
 	if (quirks & DW_UART_QUIRK_SKIP_SET_RATE)
 		p->set_termios = dw8250_do_set_termios;
+	if (quirks & DW_UART_QUIRK_NO_DLF)
+		data->data.no_dlf = true;
 	if (quirks & DW_UART_QUIRK_IS_DMA_FC) {
 		data->data.dma.txconf.device_fc = 1;
 		data->data.dma.rxconf.device_fc = 1;
@@ -892,6 +895,15 @@ static const struct dw8250_platform_data dw8250_skip_set_rate_data = {
 	.quirks = DW_UART_QUIRK_SKIP_SET_RATE,
 };
 
+/*
+ * The baud clock is the bus clock gate, whose rate cannot change, and offset
+ * 0xc0 is the RS485 control register rather than DLF.
+ */
+static const struct dw8250_platform_data dw8250_sun60i_a733_data = {
+	.usr_reg = DW_UART_USR,
+	.quirks = DW_UART_QUIRK_SKIP_SET_RATE | DW_UART_QUIRK_NO_DLF,
+};
+
 static const struct dw8250_platform_data dw8250_intc10ee = {
 	.usr_reg = DW_UART_USR,
 	.quirks = DW_UART_QUIRK_IER_KICK,
@@ -913,6 +925,7 @@ static const struct dw8250_platform_data dw8250_tda54 = {
 
 static const struct of_device_id dw8250_of_match[] = {
 	{ .compatible = "snps,dw-apb-uart", .data = &dw8250_dw_apb },
+	{ .compatible = "allwinner,sun60i-a733-uart", .data = &dw8250_sun60i_a733_data },
 	{ .compatible = "cavium,octeon-3860-uart", .data = &dw8250_octeon_3860_data },
 	{ .compatible = "marvell,armada-38x-uart", .data = &dw8250_armada_38x_data },
 	{ .compatible = "renesas,rzn1-uart", .data = &dw8250_renesas_rzn1_data },
diff --git a/drivers/tty/serial/8250/8250_dwlib.c b/drivers/tty/serial/8250/8250_dwlib.c
index 9bb02a4ab11f..9c6f3d926ad5 100644
--- a/drivers/tty/serial/8250/8250_dwlib.c
+++ b/drivers/tty/serial/8250/8250_dwlib.c
@@ -209,16 +209,18 @@ void dw8250_setup_port(struct uart_port *p)
 	}
 	up->capabilities |= UART_CAP_NOTEMT;
 
-	/* Preserve value written by firmware or bootloader  */
-	old_dlf = dw8250_readl_ext(p, DW_UART_DLF);
-	dw8250_writel_ext(p, DW_UART_DLF, ~0U);
-	reg = dw8250_readl_ext(p, DW_UART_DLF);
-	dw8250_writel_ext(p, DW_UART_DLF, old_dlf);
-
-	if (reg) {
-		pd->dlf_size = fls(reg);
-		p->get_divisor = dw8250_get_divisor;
-		p->set_divisor = dw8250_set_divisor;
+	if (!pd->no_dlf) {
+		/* Preserve value written by firmware or bootloader  */
+		old_dlf = dw8250_readl_ext(p, DW_UART_DLF);
+		dw8250_writel_ext(p, DW_UART_DLF, ~0U);
+		reg = dw8250_readl_ext(p, DW_UART_DLF);
+		dw8250_writel_ext(p, DW_UART_DLF, old_dlf);
+
+		if (reg) {
+			pd->dlf_size = fls(reg);
+			p->get_divisor = dw8250_get_divisor;
+			p->set_divisor = dw8250_set_divisor;
+		}
 	}
 
 	reg = dw8250_readl_ext(p, DW_UART_UCV);
diff --git a/drivers/tty/serial/8250/8250_dwlib.h b/drivers/tty/serial/8250/8250_dwlib.h
index ee7a07fac0f6..ca0dfd6d056e 100644
--- a/drivers/tty/serial/8250/8250_dwlib.h
+++ b/drivers/tty/serial/8250/8250_dwlib.h
@@ -88,6 +88,7 @@ struct dw8250_port_data {
 	/* Hardware configuration */
 	u32			cpr_value;
 	u8			dlf_size;
+	bool			no_dlf;		/* Offset 0xc0 is not DLF */
 
 	/* RS485 variables */
 	bool			hw_rs485_support;