diff mbox series

[net-next,v7,6/6] arm64: dts: allwinner: t527: orangepi-4a: Enable Ethernet port

Message ID 20250923140247.2622602-7-wens@kernel.org (mailing list archive)
State New
Headers
Series net: stmmac: Add support for Allwinner A523 GMAC200 |

Commit Message

Chen-Yu Tsai Sept. 23, 2025, 2:02 p.m. UTC 
From: Chen-Yu Tsai <wens@csie.org>

On the Orangepi 4A board, the second Ethernet controller, aka the GMAC200,
is connected to an external Motorcomm YT8531 PHY. The PHY uses an external
25MHz crystal, has the SoC's PI15 pin connected to its reset pin, and
the PI16 pin for its interrupt pin.

Enable it.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---

Changes since v1:
- Switch to generic (tx|rx)-internal-delay-ps properties
---
 .../dts/allwinner/sun55i-t527-orangepi-4a.dts | 23 +++++++++++++++++++
 1 file changed, 23 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
index 39a4e194712a..9e6b21cf293e 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
+++ b/arch/arm64/boot/dts/allwinner/sun55i-t527-orangepi-4a.dts
@@ -15,6 +15,7 @@  / {
 	compatible = "xunlong,orangepi-4a", "allwinner,sun55i-t527";
 
 	aliases {
+		ethernet0 = &gmac1;
 		serial0 = &uart0;
 	};
 
@@ -102,11 +103,33 @@  &ehci1 {
 	status = "okay";
 };
 
+&gmac1 {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_cldo4>;
+
+	tx-internal-delay-ps = <0>;
+	rx-internal-delay-ps = <300>;
+
+	status = "okay";
+};
+
 &gpu {
 	mali-supply = <&reg_dcdc2>;
 	status = "okay";
 };
 
+&mdio1 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+		interrupts-extended = <&pio 8 16 IRQ_TYPE_LEVEL_LOW>; /* PI16 */
+		reset-gpios = <&pio 8 15 GPIO_ACTIVE_LOW>; /* PI15 */
+		reset-assert-us = <10000>;
+		reset-deassert-us = <150000>;
+	};
+};
+
 &mmc0 {
 	vmmc-supply = <&reg_cldo3>;
 	cd-gpios = <&pio 5 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PF6 */